Modifikasi Sistem Monitoring Data Universal Testing Machine Galdabini Type PM10 dengan Berbasis Arduino Uno
DOI:
https://doi.org/10.36499/jim.v19i1.7459Keywords:
arduino uno, PLX-DAQ microsoft excel, universal testing machine.Abstract
This study aims to repair damage to the Galdabini Type PM10 Universal Testing Machine (UTM) on a data acquisition system with an automatic system, design a conventional data acquisition system to a control system using the Arduino Uno AT Mega 328 microcontroller program and process the desired data and graphics with the help of the PLX application - DAQ Ms. Excel. This research uses the experimental method which is a basic framework used as a reference in conducting research which contains stages for solving problems in research. The research was conducted at the Materials Testing Laboratory of the Pontianak State Polytechnic Department of Mechanical Engineering by designing the input and output program for the PM10 Galdabini UTM data. In the tensile test, the output data displays force and addition data, a graph of the attraction and addition force relationship. While in Ms.Excel data obtained tensile stress, strain, modulus of elasticity, the proportion of changes in length and diameter, as well as a graph of the relationship between tensile stress and strain. In testing the compression output data displays force and shortening data, a graph of the compression and shortening force relationship. In Ms.Excel data obtained compressive stress, strain, modulus of elasticity, as well as a graph of the relationship between compressive stress and strain. In the bending test, the output data displays force and deflection data, a graph of the relationship between bending and deflection forces. In Ms. Excel, we get data on bending stress, modulus of elasticity, and graphs of the relationship between bending stress and deflection.
Â
Kata kunci: arduino uno, PLX-DAQ microsoft excel , universal testing machine.
References
Bhargava, A. K. and Sharma, C. P. (2011) Mechanical Behaviour and Testing of Materials. PHI Learning.
Book Standard ASTM D638-03 (2003), Standard Test Method For Tensile Properties Of Plastics. ASTM International.
Budiman, H. (2016) ‘Analisis Pengujian Tarik (Tensile Test) Pada Baja St37 Dengan Alat Bantu Ukur Load Cell’, J-ENSITEC, 3(01), pp. 9–13. doi: 10.31949/j-ensitec.v3i01.309.
Dietser, George E, Sriatie Djaprie, 1987, Metalurgi Mekanik Jilid 1 Edisi Ketiga. Jakarta: Erlangga
Faupel, H Joseph, Fisher, E Franklin, 1981, Engineering Design, 2nd ed., John Willey and Sons, New York.
Karomi, F. I. O. S. (2020) ‘kalibrasi sensor gaya dan displacement untuk uji tarik berbasiskan arduino Calibration of force sensors and displacement for tensile test based on Arduino’, Dinamika Teknik Mesin, pp. 50–58.
Khurmi, R. . (1993) ‘Strengths of materials’, in Mechanical Engineer’s Data Handbook. Elsevier, pp. 1–55. doi: 10.1016/B978-0-7506-1014-8.50006-4.
Louis, L. (2016) ‘Working Principle of Arduino and Usig it as a Tool for Study and Research’, International Journal of Control, Automation, Communication and Systems, 1(2), pp. 21–29. doi: 10.5121/ijcacs.2016.1203.
Marrow J, 2009, The Materials Science Internet Microscope, UMIST and University of Manchester,www.umist.ac.uk/matsci.
Surdia T & Saito S, 1999, Pengetahuan Bahan Teknik. Jakarta : PT. Pradnya Paramita.
Timings RL, 1998, Engineering Materials, Volume-I, 2nd Edition Addison Wesley Longman Limited.
William D. Callister, Jr., D. G. R. (2010) ‘8.6 Fracture Toughness Testing’, Materials Science and Engineering an Introduction, 1, pp. 250–255.
Downloads
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:
The journal allow the authors to hold the copyright without restrictions and allow the authors to retain publishing rights without restrictions.
Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
This work is licensed under a Creative Commons Attribution 4.0 International License.
